David, what do you think it will take to get some 37s on there? maybe a 2" lift?

10th gen (same as this lightning) owner F150 owner here. I love these lightnings and the body style. the Eaton M112 is ok , but with forged bottom end this thing can see some pretty big power with a whipple or Kenne Bell. Throw in a T56 6 sp and its a blasty blast all around. I would remove the spoiler and crappy ebay…

large truck and honda ridgeline should not be in the same sentence. maybe small or midsize truck.

I think the best solution to protect against wheel thieves is to bag it and slam ‘er down when you park. So that the “rims” tuck up so far into the fender that access to the lugs are near impossible to reach.

Will the diesel be worth it? I’d like to get a JL, I really like all the updates they made, plus 35s with no lift is my go to (I have a set of rubbers ready to go in my garage).

I treat myself every day. Though my vision is slightly different. I see a treat as doing something different than you normally would. For example, every day I will take a different route to work. The shortest possible time to get to work takes 10 minutes, I have left super early (5:30-6AM) and taken 1.5 hours to get…

2 in the doors is pretty awesome. I hope it can fit a good size cup/ water bottle. My prius has a cup holder in the front doors but is limited to the smallest of water bottles. lame.

THAT’s WHAT I SAID! Some of the pistons and rods are still semi-attached and flopping around. granted they’re all chewed up. I assume the pressure built up in the cylinder was too much for the crank bearing cap studs/bolts which caused them to separate leaving the bottom end in tact while the top side took flight…

They’re duratrac’s though, kinda a cross between an AT and an MT. I bet as a sheriff he hauls the side by sides to patrol remote areas and hits dirt back roads, plus with it being Oregon they get snow so it helps them there.

Flannel FTW! I helped a friend do this same thing to his XJ. For some odd reason is makes it look way more classier, even with the rest of the OEM interior in good shape.

And if it arrives late to the next station I believe they will give out notices for you to give to your supervisor so your tardiness is on the training being late, not you.

I live in the DFW metroplex in Texas and see bikes lane splitting and filtering quite a bit. I am perfectly ok with it and even ooch my car to edge of the lane to give them more room. I know how much is sucks to have to sit in traffic on a 100+ degree days on a hot motorbike.

Meh, good price i guess. Compared to the Mavic (thats more than twice the cost) you get twice the speed, more than twice the distance, much better photo/video quality, better controls, and the mavic folds up smaller than the spark...

Meh, good price i guess. Compared to the Mavic (thats more than twice the cost) you get twice the speed, more than…

*most prius people.

Good on you for getting a small cheap drone to learn how to fly on! Tips: take it to a wide open spot and learn how to fly it <20ft from you at first. Learn how to fly with it facing away from you as the controls are normal, then spin it around 180 degrees so all the controls are backwards. Once you get good at this…

I know several jeep people who really like to wheel their jeeps. First mod other than the typical wheel/tire/lift/bumpers is to flushmount the tail lights. Any branch that catches the light just right tends to rip them right off. I’ve seen it happen and it tears up the metal around the light. Better get to choppin up…

I’m partial to white if the scheme looks right, like a ratrod. Other than that I haven’t seen a cool color in a while, other than that terrain color Ford put on the Raptors. My best friend has a gray C6 vette...talk about super lame. 

That truck is just as sick as the original one they built!

I haven’t held back at all. I think my biggest issue is downloading models from the internet, some are really good and print quicky and some have glitches and makes the print twice as long as it should be and leaves gaps in the print. I know this is the cad file because when I make my own models in SolidWorks they…

I haven’t held back at all. I think my biggest issue is downloading models from the internet, some are really good…

These are some pretty good deals!

These are some pretty good deals!